How to Cut, Connect, Fit and Wire LED Strip Lights

Quick answer: Sensio LED strip lights can be cut at the marked cut points, and the free-cut X range can be cut anywhere. Join runs or turn corners with the matching clips, leads and corner connectors. The strip plugs into a 24V LED driver, sized with 10% spare capacity, with no soldering needed. Mains connection to the driver should be made by a qualified electrician.

This guide covers the questions installers ask most about LED strip lights: where you can cut them, how to join them, how to connect and wire them, and how to fit them so they look right. It covers Sensio's 24V flexible strips, including our free-cut X range, which you can cut at any point.

Can you cut LED strip lights?

Yes. Our free-cut X range can be cut at any point (see below). Our other flexible LED strips can be cut to length, but only at the marked cut points. The cut marks are shown on the strip, and the spacing depends on the strip. Cutting anywhere else will stop that section of the strip working.

Strip Cut every Type
Neutron™ 25mm Single colour, 3.5mm wide
Delta™ 25mm Single colour, silicone, three-sided light
Polar Pro™ 31mm CCT, COB
Razor™ 25mm Edge-lit for handleless kitchens
Viva 3™ 50mm Single colour, IP54
Sigma 2™ 50mm Single colour, bends round flat corners
Radiant Pro™ 50mm CCT, diffused silicone
Ion 5™ and Ion 8™ 50mm CCT
Primo 2™ and Dart™ 100mm Single colour
Flux™ 142.5mm RGB and CCT colour changing

Strips with closer cut marks, such as Neutron, let you cut nearer to the exact length you need, which reduces dark spots at the ends of a run.

Free-cut strips you can cut anywhere

Our X range strips are free cut. You can cut them at any point along the strip, with no cut marks to find and no gaps at the end of a run, so the light runs right to the end of the cabinet, plinth or shelf. Both pieces keep working after a cut.

Strip Type How to fit
Polar X™ Single colour COB Surface, VHB adhesive; no profile needed
Polar X Pro™ CCT COB Surface, VHB adhesive
Polar X Duo™ Duo COB (4000K / 2700K) Surface, VHB adhesive
Polar X IP65™ Single colour COB, IP65 Bathroom use, see the bathroom section below
Primo X™ Single colour Surface, VHB adhesive
Radiant X™ Single colour Recessed push-fit, or surface with Radiant brackets
Razor X 2mm™ and 2mm Duo™ Edge-lit COB Recessed into a 2mm saw cut or routed channel
Razor X 4mm™ and 4mm Duo™ Edge-lit COB Recessed into a groove from a standard saw blade or router
Razor X Pro 2mm™ and 4mm™ CCT edge-lit COB Recessed, as above
Affinity™ Faraday X Single colour COB, magnetic Fits to the Affinity magnetic track

Polar X IP65 needs its cut end resealed or fitted with an end cap to keep its IP65 rating. The other X strips need no sealing after a cut.

How to cut LED strip

  1. Measure the run. For X range strips, cut at the exact length you need. For other strips, find the nearest cut mark to that length.
  2. Cut straight across the strip with sharp scissors, through the middle of the cut mark where there is one.
  3. Keep the offcut. On many of our strips it can be used again (see joining below).
  4. Where the strip comes with end caps, such as Radiant Pro, fit one to the cut end for a clean finish.

Rather have it cut for you? Our TrueFIT bespoke cutting and soldering service supplies strip cut to length and ready to fit.

How to join LED strip and get round corners

You can use the whole reel without waste. Cut sections of Ion 8, Primo 2, Dart and Sigma 2 can be reused with the matching joining clips and interconnecting leads, sold separately. Viva 3 can be cut once and the cut-off section reused with a connector clip and interconnecting lead.

Several strips, including Neutron, Polar Pro, Razor, Ion 5 and Radiant Pro, have driver connection cables pre-soldered at both ends, so you can cut the reel and power both pieces as two separate runs.

Joining and powering free-cut X strips

Polar X, Polar X Pro, Polar X Duo, Primo X, Razor X and Razor X Pro all have driver connection cables pre-soldered at both ends. Cut the reel and you can power both pieces as separate runs. To use further cut lengths, add an additional driver connection cable, such as the Polar X 2500mm driver connection cable, sold separately.

Polar X and Primo X can also be joined after a free cut. They have their own joining clips, 50mm corner connectors and 1500mm interconnecting cables, so cut sections can be joined or taken round a corner. Razor X and Radiant X are powered as separate runs.

Affinity Faraday X connects to the Affinity track with the flexible strip connector. Each reel comes with two.

For corners on other strips, use the corner connectors made for each strip, or choose Sigma 2, which has a zig-zag board that bends around 90 degree flat corners without a corner cable. Silicone strips such as Radiant Pro and Delta bend around curves on islands and cabinetry.

Video: how to connect LED strip lights with connection leads

See the step by step how to connect LED strip lights video guide, the leads and connectors in our cables and connections range, or browse all our video guides.

How to connect LED strip to power

Our flexible strips run at 24V and connect to a Sensio 24V driver, which converts mains power to 24V.

  • Single colour strips connect to our 2-pin drivers.
  • CCT strips, such as Polar Pro and Ion 5, use 4-pin connectors.
  • RGB and CCT strips, such as Flux, use the RGBCCT receiver or Titan RGBCCT smart driver.
  • Viva 3 needs the 2500mm driver connection cable (SE10314), sold separately unless bought in a kit.

Choose a driver large enough for the total length of strip on it. Use the driver calculator to work out the size, and browse our 24V LED drivers. Because the strip runs at 24V, long runs keep an even light without fading. The mains connection to the driver should be made by a qualified electrician in line with BS 7671 (IET Wiring Regulations). Our guide what is an LED driver explains each option, and the driver installation video shows it step by step.

How to wire LED strip lights

Our strips run at 24V. The driver changes mains power into 24V, and the strip plugs into the driver with its driver connection cable. No soldering is needed for a standard installation.

Add up the total length of strip on the driver and choose a driver with enough capacity, leaving 10% spare. In other words, load a driver to no more than 90% of its rating. The driver calculator works this out for you.

Our 25m strips can be run from one end with no light fade. The limit is the connector: put no more than 60W (3A) through a single JB4 connector.

Duo strips change between 4000K and 2700K using the Duo Flexible Strip Adaptor. Do not use a Duo strip on a CCT driver. Use a 2-pin driver with the Duo Flexible Strip Adaptor.

The mains connection to the driver should be made by a qualified electrician in line with BS 7671 (IET Wiring Regulations).

LED strip in bathrooms

Polar X IP65 is our strip for bathrooms. It is rated IP65 and approved for bathroom Zone 1 (and therefore Zone 2). It has a natural white (4000K) light and comes with pre-soldered 2.5m driver connection cables at each end, fitted with IP65 connectors. If you cut it, reseal the cut end or fit an end cap to keep the IP65 rating.

The Titan IP44 driver can go in Zone 2. It must not go in Zone 0 or Zone 1. Our bathroom zones and IP ratings guide explains where each rating can be used.

How to fit LED strip

  1. Make sure the surface is clean, dry and free of dust before you stick the strip down.
  2. Peel back the VHB (Very High Bond) tape on the back of the strip a little at a time and press it firmly into place.
  3. For a neat, diffused line of light, fit the strip into an aluminium profile. Check each strip's page for the profile ranges it suits.
  4. Radiant Pro pushes into a recess for a flush finish, or can be surface mounted with its brackets. Razor fits into a narrow routed channel made with a simple saw cut.

Recessed strip for handleless and grooved designs

Razor X is edge lit and only 2mm or 4mm wide. It push-fits into a narrow channel, so no adhesive is needed. The 2mm version fits a saw cut or routed channel. The 4mm version fits a groove from a standard saw blade and suits CNC or hand routing, on site or in the factory.

Radiant X also push-fits into a recess, or surface mounts with Radiant brackets, and bends round corner recesses.

Strip Groove width Groove depth
Razor X 2mm 2mm 10mm
Razor X 4mm 4mm 10mm
Radiant X 4mm 10mm

Dimming and control

Single colour strips dim with a Sensio single-colour receiver. CCT strips work with the CCT receiver and remote, or the Titan Smart Kinetic Driver to control, zone and dim the lights. See our guide to Titan smart drivers and the driver and remote control setup video. Setup videos: single colour receiver, CCT receiver and RGBCCT receiver.

More videos: watch the LED strip lighting video playlist on YouTube, or see all our video guides.

Frequently asked questions

Can you cut LED strip lights anywhere?

Our free-cut X range can be cut at any point. Our other strips can only be cut at the marked cut points, which are shown in the cut table above.

Can you cut LED strip lights and still use them?

Yes. On X range strips both pieces keep working wherever you cut. On other strips, cut on the marked cut points. Both pieces can be used where the strip has connection cables at both ends, or with joining clips and leads.

What happens if I cut between the cut marks?

On strips with cut marks, the section you cut through will not light. Always cut across the middle of a marked cut point. This does not apply to free-cut X range strips.

How do I connect two pieces of LED strip?

Use the joining clip and interconnecting lead made for that strip, sold separately. Check the strip's product page for the matching accessories.

How long do LED strip lights last?

LED strip lasts far longer than traditional bulbs. Sensio electrical components, including the LEDs, are covered by our guarantee of up to 7 years; check each product page for its guarantee period and see our guarantee.

Do LED strip lights use a lot of electricity?

No, LED strip uses little power compared with traditional lighting. Each strip's wattage is shown in the specification on its product page; multiply it by the length fitted and the hours used to estimate energy use.

Are LED strip lights safe to leave on?

Our strips run at low voltage (24V) from a driver. For a safe installation, use the right size driver loaded to no more than 90%, fit the strip to a clean, dry surface or an aluminium profile, use IP-rated strip in bathrooms, and have the mains connection to the driver made by a qualified electrician.

How do you wire LED strip lights to a plug?

Use the Modus Plug-in 30W driver. The strip connects to the driver with its connection cable, and the driver plugs into a standard socket.

Can you connect LED strip lights straight to the mains?

No. Our strips run at 24V, so they connect to the mains through a 24V LED driver. The mains connection to the driver should be made by a qualified electrician in line with BS 7671 (IET Wiring Regulations). For a single run with no wiring, the Modus Plug-in 30W driver plugs into a standard socket.

Do LED strip lights need a driver?

Yes. Our strips run at low voltage, most of them 24V, so they need an LED driver to convert mains power.

What size driver do I need?

It depends on the total length and wattage of strip on the driver. Leave 10% spare capacity. Use the driver calculator.

Can LED strip lights go in a bathroom?

Yes, if the strip has the right IP rating for the zone. Polar X IP65 is approved for Zone 1 (and therefore Zone 2).

Can LED strip go round corners?

Yes, with a corner connector, or with Sigma 2, which bends around 90 degree flat corners. Silicone strips bend around curves.

Do I need a profile for LED strip?

It depends on the installation. Any of our surface-mounted strips can be used without a profile. COB strips such as Polar X are fully diffused, so they will not show visible dots, even without a profile. Non-COB strips may show dots from the individual diodes. Whichever strip you use, a profile gives a better effect: a more integrated, softer light that looks more premium.

Need help with a project? Get in touch with our technical team, or find a distributor.

Reading next

LED under cabinet lighting over a kitchen worktop
Sensio Titan 24V LED driver installed in a kitchen