Quick answer: An LED driver converts mains power to the low voltage LED lights and LED strip need. Most drivers are either constant voltage, which hold a set voltage such as 24V, or constant current, which hold a set current in milliamps. LED strip uses constant voltage, and Sensio drivers give 24V. To choose one, match the pin type of the lights (2-pin single colour and TrioTone®, 4-pin CCT, 6-pin RGBCCT), pick a driver rated higher than the total wattage, then choose the control you want (sensor, wall dimmer, remote or app). The driver calculator works out the size for you.
Every 24V LED light needs a driver. It's the part that powers the whole system, and the wrong one can cause flicker, poor performance or early failure. Choosing the right one comes down to four checks: the pin type of the lights, the total wattage, how the lights will be controlled, and where the driver will sit. If you are replacing an old halogen transformer, read LED driver vs transformer first, as it is not a like for like swap.
What an LED driver does
An LED driver converts mains power to the low voltage that LED lights and LED strip need. You will also see it called an LED transformer or LED power supply. Sensio drivers give a 24V output and have built-in distribution ports, so several lights can plug into one driver.
Constant voltage vs constant current
LED drivers generally come in two types. The difference is what the driver holds steady.
| Constant voltage | Constant current | |
|---|---|---|
| What it holds steady | The voltage, such as 12V or 24V | The current, measured in milliamps (mA) |
| What changes | The lights draw the current they need | The voltage varies with the load |
| Generally used for | LED strip, and lights labelled with a voltage | Lights labelled with a current rather than a voltage |
| How to match it | Same voltage as the lights, rated above their total wattage | Exactly the current the light is labelled with |
| Sensio | Sensio 24V drivers are constant voltage | Not used for Sensio 24V strip |
The rule is simple: match the driver to what the light is labelled with. For another brand's lights, check the label or ask the manufacturer first, as the wrong type can damage them.
Why Sensio LED strip uses 24V constant voltage
LED strip is a constant voltage product, and Sensio designs its strip and lights around 24V. The driver connection cable on each strip plugs straight into a Titan driver's distribution ports, with no soldering.
- Half the current. For the same wattage, a 24V system draws half the current of a 12V one, so it runs more efficiently.
- Stays cooler. Less heat means cooler running and a longer life for the lights.
- Less voltage drop. Longer runs of light with no loss of brightness along the run. Polar X, for example, runs up to 25m without fading at the far end.
Read more in 12V or 24V LED strip lights.
Step 1: match the pin type
- 2-pin for single colour and TrioTone® (colour selectable) lighting.
- 4-pin for CCT (colour adjustable) lighting, to move between warm and cool white.
- 6-pin for RGBCCT colour changing strip, such as Flux and Polar RGBCCT.
The pin type is shown on each light's product page.

Step 2: add up the wattage
Add together the wattage of every light and the total length of strip that will run from the driver, then choose a driver rated higher than that total. Our drivers run from 6W to 150W. For wattage tables of our strips and lights, worked examples and a quick calculator, read what size LED driver do I need. For strip on its own, the LED strip calculator lets you pick each Sensio strip by name. The driver calculator also suggests the controls and accessories you need.
Step 3: choose how the lights will be controlled
| Driver | Pins | Control |
|---|---|---|
| Titan+™ | 2-pin | Plug-in sensors (PIR, IR, switch and door). Dimmable only when paired with a sensor. Not for use with a wall dimmer. |
| Titan™ Dimmable | 2-pin | Wall dimmable from a mains dimmer switch, with a 5% to 100% dimming range. |
| Titan™ Smart Kinetic | 2-pin | Link Sensio app, Amazon Alexa and Google Assistant, and the wireless Titan Kinetic Switch. |
| Titan™ Smart Kinetic CCT | 4-pin | As above, for CCT lighting, including colour changing and schedules. |
| Titan™ Smart RGBCCT | 6-pin | App and voice control for Flux and Polar RGBCCT strip. |
| Modus™ Plug-in 30W | Single colour or TrioTone® | Plugs straight into a socket for easy retrofit. Works with Affinity magnetic track. |
Want to dim? Read can you dim LED strip lights to see which drivers work with a wall dimmer switch and which dim by sensor, remote or app.
Matching the control to the light
- Single colour: a simple wall switch, such as the Titan Smart Kinetic Switch with the Titan Smart Kinetic Driver.
- TrioTone®: the same options, or for more discreet control, the Titan+ Driver with a wireless PIR, IR, touch or door sensor. See which LED light sensor you need.
- CCT: the Titan+ Driver with a CCT Receiver and the Universal Remote Control, or the Titan Smart Kinetic CCT for app control.
- RGB colour changing: the Titan Smart RGBCCT Driver with Alexa or the Link Sensio app, or the Titan+ Driver with an RGB Receiver and the Universal Remote Control.
Read more in our guide to Titan smart drivers.
Watch: choosing and installing a Titan driver
See how to choose and install the Titan+ 24V driver with a mains switch and sensors.
Step by step video guides: how to choose and install a 24V LED driver and how to set up a 24V LED driver with a remote control. Using a wall dimmer? Watch the Titan Dimmable driver installation and setup guide. For app and switch control, watch the Titan Smart Kinetic setup guide, or browse all our video guides.
Step 4: plug-in or hard-wired, and where the driver goes
Plug-in. The Modus™ Plug-in is a 30W 24V driver that plugs straight into a standard UK socket, so lights can be added without new wiring to the mains. It suits retrofits and works with Affinity magnetic track, single colour and TrioTone® lighting.
Hard-wired. If you want the lights on a wall switch or a wall dimmer, the driver is wired into the lighting circuit. Titan drivers come with a 2m mains cable; a cable with plug is sold separately. Connection to the mains should be carried out by a qualified electrician.
Kitchens and furniture. Titan drivers are a slim 16mm deep, so they fit behind kickboards and above wall units.
Bathrooms. Keep the driver out of zones 0 and 1. The Titan IP44 Driver is a 30W IP44 rated driver that can go in zone 2 (not zone 0 or zone 1), with an IP44 connection ready to plug and play with Sensio 24V lights. Check the zones in our bathroom zones guide.
If your lights flicker once installed, work through our checklist: why are my LED strip lights flickering?
More videos: watch the Drivers, sensors and smart control video playlist on YouTube, or see all our video guides.
Frequently asked questions
What is an LED driver used for?
It converts mains power to the low voltage LED lights run on. Without the right driver, LEDs can flicker, underperform or fail early.
What is the difference between constant voltage and constant current?
A constant voltage driver holds a set voltage, such as 24V, and the lights draw the current they need. A constant current driver holds a set current in milliamps and the voltage varies. LED strip uses constant voltage.
Can I use a constant current driver with LED strip?
No. LED strip needs a constant voltage driver at the strip's voltage. Sensio strip runs at 24V, so use a 24V Sensio driver with the matching pin type.
What size LED driver do I need?
One rated higher than the total wattage of the lights and strip on it. Our guide to what size LED driver you need has wattage tables, worked examples and a calculator.
Is an LED driver the same as an LED transformer?
The terms are often used for the same thing: a unit that converts mains power to the low voltage LED lights need. Sensio lighting runs at 24V, so use a 24V driver with the matching pin type.
Can I use a 12V driver with 24V lights?
No. The driver's output must match the lights. Sensio lights run at 24V, so use a 24V Sensio driver.
Should I choose a plug-in or hard-wired LED driver?
Plug-in, such as the Modus™, if you want to add lights without new mains wiring. Hard-wired if you want the lights on a wall switch or wall dimmer, with the mains connection made by a qualified electrician.
Can I use a wall dimmer with LED lights?
Only with a driver designed for it. The Titan Dimmable driver works with a mains wall dimmer. Titan+ and the smart drivers must not be used with a wall dimmer; they dim through sensors, the app or the Kinetic Switch. See can you dim LED strip lights.
Can one driver run several lights?
Yes. Titan drivers have built-in distribution ports, and port expanders add more connections, as long as the total wattage stays within the driver's rating.
Can an LED driver go in a bathroom?
Keep it out of zones 0 and 1. The Titan IP44 Driver is IP44 rated and can go in zone 2. See our bathroom zones guide.
Can I control the lights from my phone?
Yes, with a Titan Smart Kinetic or Smart RGBCCT driver and the Link Sensio app, or by voice with Amazon Alexa or Google Assistant.
Browse the full 24V LED driver range, or contact our technical team for help with a specification.





